行業新聞

當前位置:網站首頁 > 新聞中心 > 行業新聞

  • 全自動熱熔焊機的主要功能
  • 本站編輯:杭州先創熱熔設備廠發布日期:2019-08-01 12:09 瀏覽次數:
全自動熱熔焊機控制箱連有一個壓力傳感器和溫度探頭,可控制和調節加熱板溫度,也能控制焊接過程中預熱階段、吸熱階段、轉換階段、焊接階段、冷卻階段等5個階段的時間參數。工作時允許各階段設置不同的壓力及維持時間并記錄,每個工作循環可自動記錄并重復操作。一組新的焊接參數被選定,如果實際參數超差,將會出現報警提示。
 
The control box of fully automatic hot melt welding machine is connected with a pressure sensor and a temperature probe, which can control and adjust the temperature of heating plate. It can also control the time parameters of five stages in the welding process: preheating stage, endothermic stage, conversion stage, welding stage and cooling stage. Different pressure and maintenance time are allowed to be set and recorded in each stage. Each working cycle can be automatically recorded and operated repeatedly. A new set of welding parameters is selected. If the actual parameters are out of tolerance, an alarm will appear.
 
 
全自動熱熔焊機一般具有以下功能:
 
Fully automatic hot melt welding machine generally has the following functions:
 
 
 
1、可以實現一致、可靠、可重復的操作;
 
1. It can achieve consistent, reliable and repeatable operation.
 
 
 
2、系統將控制監視并記錄焊接過程中各階段的主要參數,以判斷每一焊口的狀況;
 
2. The system will control, monitor and record the main parameters of each stage in the welding process to judge the condition of each welding joint.
 
 
 
3、焊機有數據檢索存儲裝置和數據下載接口,能存貯和下載焊接數據;
 
3. The welding machine has data retrieval storage device and data download interface, which can store and download welding data.
 
 
 
4、銑削管道端面后,能夠自動檢查管道是否夾裝牢固;
 
4. After milling the end face of the pipeline, it can automatically check whether the pipeline is clamped firmly or not.
 
 
 
5、自動測量拖動壓力以及自動補償拖動力;
 
5. Automatic measurement of drag pressure and automatic compensation of drag power;
 
 
 
6、根據選定參數自動監控熱板溫度,只有熱板溫度在設定的工作溫度范圍內時,焊機才能進行焊接;
 
6. Hot plate temperature can be automatically monitored according to the selected parameters. Only when the hot plate temperature is within the set working temperature range, the welding machine can be welded.
 
 
 
7、熱板放入待焊兩管材端面之后的所有階段(加壓、卷邊、降壓力降至拖動壓力、吸熱壓力和時間、切換:機架打開/熱板抽出/機架閉合、加壓、保壓、冷卻)自動進行;
 
7. All stages (pressure, edge rolling, pressure drop to drag pressure, endothermic pressure and time, switching: rack opening/hot plate extraction/rack closing, pressurization, holding pressure and cooling) are automatically carried out after the hot plate is put into the end face of the two pipes to be welded.
 
 
 
8、微處理器采用閉環控制系統。
 
8. Microprocessor adopts closed-loop control system.

浙公網安備 33011002012312號

竞彩销售时间